Showing 1 - 20 of 935
ASME
ASME B18.6.1
1997
English

WOOD SCREWS

This standard covers the complete general and dimensional data for the various types of slotted and recessed head wood screws recognized as "American National Standard." Also included are appen [...]
DIN EN
DIN EN 10270-1
2012
English, German

Steel wire for mechanical springs – Part 1: Patented cold drawn unalloyed spring steel wire

1.1 This European Standard applies to patented cold drawn unalloyed steel wire of circular cross-section for the manufacture of mechanical springs for static duty and dynamic duty applications. [...]
SAE
SAE AS568
2001
English

Aerospace Size Standard for O-Rings

This Aerospace Standard specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread [...]
ASTM
ASTM D2000
2001
English

Standard Classification System for Rubber Products in Automotive Applications

1.1 This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but [...]
Others
MPIF 35
2016
English

Materials Standards for Metal Injection Molded Parts

MPIF Standard 35 is issued to provide the design and materials engineer with the information necessary for specifying powder metal (PM) materials that have been developed by the PM parts manufa [...]
IFI
IFI-301
2008
English

GAGE CALIBRATION REQUIREMENTS AND PROCEDURES FOR THREAD GAGES

All UN, UNJ, M, and MJ thread form gages shall be calibrated using the commonly accepted metrology techniques described in this standard using properly maintained standard metrology equipment. [...]
IFI
IFI-166
2007
English

INSPECTION PROCEDUR FOR THREAD NICKS – INCH SERIES

This standard establishes an inspection procedure to determine acceptability of thread nicks as they relate to screw thread assemblability. This procedure is intended to be used for bolts, scre [...]
IFI
IFI-143
2007
English

TEST FOR EVALUATING THE TORQUE-TENSION RELATIONSHIP ON BOTH EXTERNALLY AND INTERNALLY THREADED FASTENERS

This standard provides a test method for determining the torque-tension relationship on both external and internal threaded fasteners for the purpose of measuring the frictional characteristics [...]
ASTM
ASTM F1470
2009
English

STANDARD PRACTICE FOR FASTENER SAMPLING FOR SPECIFIED MECHANICAL PROPERTIES AND PERFORMANCE INSPECTION

Throughout this practice the terms detection and prevention apply to quality control systems. A brief description of both is provided to assist the purchaser in the application of this practice [...]
ASTM
Abstract of ASTM F812/F812M
2007
English

SURFACE DISCONTINUITIES OF NUTS

This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of inch-series nuts with nominal diameters [...]
ASTM
Abstract of ASTM F788/F788M
2008
English

SURFACE DISCONTINUITIES OF BOLTS, SCREWS, AND STUDS

This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolt, screws, and studs, including heat- [...]
ASTM
ASTM F606
2010
English

TEST METHODS FOR DETERMINING THE MECHANICAL PROPERTIES OF EXTERNALLY AND INTERNALLY THREADED FASTENERS, WASHERS, AND RIVETS

1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension ind [...]
ASME
ASME B18.18
2011
English

QUALITY ASSURANCE FOR FASTENERS

This quality focused Standard establishes in-process and final inspection requirements for fastener products as well as a receiving inspection plan for fastener purchasers. This Standard identi [...]
ASME
ASME B18.2.9
2010
English

STRAIGHTNESS GAGE AND GAGING FOR BOLTS AND SCREWS

1 SCOPE This Standard describes a gage and procedure for checking bolt or screw straightness at maximum material condition (MMC) and provides default limits when not stated in the applicable pr [...]
ASTM
ASTM F2329
2005
English

ZINC COATING, HOT-DIP, REQUIREMENTS FOR APPLICATION TO CARBON AND ALLOY STEEL BOLTS, SCREWS, WASHERS, NUTS AND SPECIAL THREADED FASTENERS

1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners applied by the hot-d [...]
ASTM
ASTM F1941
2010
English

ELECTRODEPOSITED COATINGS ON THREADED FASTENERS (UNIFIED INCH SCREW THREADS (UN/UNR))

This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with unified inch screw threads. It specifies coating thickne [...]
ASTM
ASTM B695
2009
English

COATINGS OF ZINC MECHANICALLY DEPOSITED ON IRON AND STEEL

This specification covers the requirements for a coating of zinc mechanically deposited on iron and steel basis metals. The coating is provided in several thicknesses up to and including 107 μm [...]
ASME
ASME B18.8.2
2005
English

TAPER PINS, DOWEL PINS, STRAIGHT PINS, GROOVED PINS AND SPRING PINS (INCH SERIES)

This standard is intended to cover the complete dimensional and general data for taper pins, recognized as “American National Standard," which are widely used in general industrial applications [...]
ASME
ASME B18.8.1
2005
English

CLEVIS PINS AND COTTER PINS (INCH SERIES)

This standard covers the complete dimensional and general data for clevis pins recognized as "American National Standard."
IFI
IFI-137
2008
English

INSPECTION AND QUALITY ASSURANCE FOR GENERAL PURPOSE BLIND RIVETS

This standard outlines the inspection plan to be used when lot compliance after shipment of general purpose blind rivets is questioned by the user. The producer is responsible for supplying a p [...]
12...47