1995
English
Headed studs
This Japanese Industrial Standard specifies the steel headed studs (hereafter referred to as "studs") used with being attached to steel beams by arc stud welding mainly for preventing slippage of composite girder construction of steel and concrete in civil engineering and architectural structures...
2001
English
Weld nuts
This Japanese Industrial Standard specifies steel weld nuts (hereafter referred to as “nuts”) for general purpose. These nuts are used for projection welding or spot welding.
1994
English
Weld bolts
This Japanese Industrial Standard specifies steel weld bolts, hereafter referred to as "bolts", for general purpose. This bolt is intended to be projection-welded at its bearing surface side of head for service, but the bolt to be welded at the top surface of head for service is excluded.
2000
English
Hexagon socket countersunk head screws
This Standard specifies the characteristics of hexagon socket countersunk head screws with threads from M3 up to and including M20, of product grade A and property classes 8.8, 10.9 and 12.9. If, in special cases, specifications other than those listed in this Standard are required, they should ...
2005
English
Hexagon nuts with flange
This Standard specifies the characteristics of hexagon nuts with flange. If, in special cases, specifications other than those listed in this Standard are required, they should be selected from existing standards, for example JIS B 0205-2, JIS B 0209-2, JIS B 1052 and JIS B 1054-2. NOTES 1 Hex...
1999
English
Hexagon nuts with flange
This Japanese Industrial Standard has been prepared based on ISO 4161 Hexagon nuts with flange — Product grade A, issued as the first edition in 1983. The text of this Standard incorporates the technical contents of the corresponding International Standard without any changes. However, the Annex ...
2005
English
Hexagon flange bolts
This Japanese Industrial Standard has been prepared based on ISO 15071 Hexagon bolts with flange—Small series—Product grade A and ISO 15072 Hexagon bolts with flange with metric fine pitch thread—Small series—Product grade A published in 1999 as the first edition by editing and integrating the co...
1995
English
Cross recessed head screws with captive washer
This Japanese Industrial Standard specifies steel or brass made cross recessed head screws with captive washer for general purposes. The cross recessed head screw with captive washer is a screw of which the threads are rolled after a washer has been assembled on the screw blank so as to prevent t...
1995
English
Hexagon head screws with captive washer
This Japanese Industrial Standard specifies steel and brass hexagon head screws with captive washer for general purposes. The hexagon head screw with captive washer is a hexagon head screw of which the threads are rolled after a washer has been assembled on the screw blank so as to prevent the di...
2017
English
Electrolytic cathodic protective surface treatment with friction requirements, Y 1300
Surface treatment Y 1300 covers different surface treatment classes. The class of the treated component is determined by the relevant environmental and finish requirements. This standard covers electrolytic cathodic protective surface treatment free from hexavalent chromium for corrosion protect...
2015
English
Cathodically protective surface treatment with friction requirement Y 1000
Surface treatment Y 1000 covers different surface treatment classes. The class of the treated component is determined by the relevant requirements for finish and environment. This standard covers coatings free from hexavalent chromium for corrosion protection of threaded iron and steel parts wit...
1960
English
Electro Screw Thread “Go” and “Not Go” Thread Ring & Plug Gauges
1) The manufacturing tolerance on h applies to an optional number of threads within gauge dimension b. 2) d3 = low limit of major diameter of bolt thread to DIN 40400 3) d1 = high limit of major diameter of bolt thread to DIN 40400 4) d2 = high limit of minor diameter of bolt thread to DIN 40400
1995
English
Sets of high strength hexagon bolt, hexagon nut and plain washers for friction grip joints
This Japanese Industrial Standard specifies the sets of high strength hexagon bolt, hexagon nut and plain washers for friction grip joints (Hereafter referred to as "sets") used mainly for steel structures.
1994
English
Wing nuts
This Japanese Industrial Standard specifies the metallic wing nuts {hereafter referred to as "nut"), for general use.
1994
English
Wing bolts
This Japanese Industrial Standard specifies the metallic wing bolts (hereafter referred to as "bolts"), for general use. Furthermore, these bolts have their heads (wing parts) firmly joined together with shanks by welding, caulking or other suitable methods, or those formed into one body.
2001
English
Domed cap nuts
This Japanese Industrial Standard specifies the steel domed cap nuts (hereafter referred to as “steel nuts”) , the stainless steel domed cap nuts (hereafter referred to as “stainless steel nuts”) , and the brass domed cap nuts (hereafter referred to as “brass nuts”), all for general use.
1995
English
Square head bolts
This Japanese Industrial Standard specifies the steel square head bolts for general use (hereafter, referred to as "bolts"). Further, the strength class column II (4T) of mechanical properties specified in this Standard will be abolished on April 1, 1999.
2004
English
Hexagon nuts and hexagon thin nuts
This Japanese Industrial Standard has been prepared based on the third edition of ISO 4032 : 1999 Hexagon nuts, style 1-Product grades A and B published in 1999, the second edition of ISO 4033 Hexagon nuts, style 2-Product grades A and B published in 1999, the third edition of ISO 4034 Hexagon nu...