2001
English
Aerospace Size Standard for O-Rings
This Aerospace Standard specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitabl […]
2011
English
MECHANICAL AND MATERIAL REQUIREMENTS FOR STEEL NUTS
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in., inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 […]
2011
English
MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
This SAE standard covers the mechanical and material requirements for inch-series steel bolts, screws. studs. screws for sems, and U-bolts used in automotive and related industries in sizes to 1-1/2 in. inclusive. The term “stud" as referred to herein applies to a cylindrical rod of mode […]
2005
English
SALT SPRAY TESTING AND EVALUATION OF FASTENER FINISHES
This procedure is used to test and evaluate the resistance of fastener surface finishes to laboratory salt spray testing.
2009
English
Quick Connect Coupling Specification for Liquid Fuel and Vapor/Emissions Systems
This SAE Recommended Practice defines the minimum functional requirements for quick connect couplings used for supply, return, and vapor/emission fuel system connections. This document also defines standard male tube end form dimensions, so as to guarantee interchangeability between all c […]
1996
English
METRIC THREAD ROLLING SCREWS
This SAE standard covers requirements for metric thread rolling screws suitable for use in general engineering applications. Requirements for three material-process options are stated: a. Screws (in sizes M2 x 0.4 thru M12 x 1.75) manufactured from low carbon steel, carburized, and temp […]
1983
English
MECHANICAL AND MATERIAL REQUIREMENTS FOR METRIC EXTERNALLY THREADED STEEL FASTENER
1.1 This standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. 1.2 Products included are bolts, screws, studs, U- […]
1998
English
MECHANICAL AND QUALITY REQUIREMENTS FOR TAPPING SCREWS
1.1 This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are c […]
1961
English
Rod Ends and Clevis Pins
The following publications form a part of the specification to the extend specified herein. Unless otherwise indicated the latest revision of SAE publications shall apply. SAE J1010-Emission Control Hose SAE J1111-Component Nomenclature-Skidder-Grapple
1994
English
SURFACE DISCONTINUITIES ON BOLTS, SCREWS, AND STUDS IN FATIGUE APPLICATIONS
This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies […]
1996
English
DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special […]
1997
English
THREAD ROLLING TAPPING SCREWS
This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance re […]
1998
English
Steel Self-Drilling Tapping Screws
1.1 General—This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapp […]
2001
English
Screw Threads – UNJ Profile, Inch
This SAE Aerospace Standard (AS) specifies the characteristics of the UNJ profile inch series of screw threads, to include a mandatory controlled radius of 0.18142P to 0.15011P at the root of the external thread and with a minor diameter of both external and internal threads increased to […]
1999
English
MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
This SAE standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, SEMS, and U-bolts used in automotive and related industries in sizes to 1-1/2 in. inclusive. The term "stud" as referred to herein applies to a cylindrical rod of moderate length […]