ASTM A502

Standard Specification for Steel Structural Rivets

English 1993
0.000
ASTM
Detailed Information

1.1 This specification covers three grades of steel rivets in diameters from 1/2 to 1 1/2 in. ( 13 to 38 mm), inclusive, for
structural fabricating purposes. The grades are as follows:
1.1.1 Grade 1 is a carbon steel rivet for general purposes.
1.1.2 Grade 2 is a carbon-manganese steel rivet suitable, with proper riveting technique, for use with high-strength carbon and high-strength low-alloy structural steels.
1.1.3 Grade 3 is similar to Grade 2 with enhanced atmospheric corrosion resistance and weathering characteristics comparable to that of steels in Specification A 588/A 588M.The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition (see 5.2). When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for
information only.

Download File
(Log in to download spec.)

Check out other specifications

DIN EN
DIN EN 10130
1991
English

Cold rolled flat steel products for cold forming – Technical delivery conditions – English version of DIN EN 10130

This European Standard applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm for cold forming, with a minimum thickness of 0,35 mm, and unles [...]
SAE
SAE J2044
2009
English

Quick Connect Coupling Specification for Liquid Fuel and Vapor/Emissions Systems

This SAE Recommended Practice defines the minimum functional requirements for quick connect couplings used for supply, return, and vapor/emission fuel system connections. This document also def [...]
ASTM
ASTM F1941/F1941M
2015
English

Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric

1.1 This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with unified inch and metric screw threads, but it may al [...]
5.01
DIN
DIN 977
1998
English

Hexagon weld nuts with flange

This standard specifies requirements for hexagon weld nuts with flange, with size M5 to M16 metric threads (coarse) or 12 mm to 16 mm diameter threads (fine), of product grade A. Weld nuts conf [...]
DIN
DIN 46241-1
1956
English

Telecommunications Engineering – Contact Rivets – Solid or Clad – Technical Conditions of Delivery

These conditions of delivery apply to solid and clad contact rivets according to DIN 46240 Sheet 1 made of contact materials which can be shaped by nonoutting methods, e.g. silver , and contact [...]
ASME ANSI
ASME/ANSI B18.18.3M
1993
English

INSPECTION AND QUALITY ASSURANCE FOR SPECIAL PURPOSE FASTENERS

This standard outlines a Quality Assurance Plan for internally and externally threaded fasteners and accessories or associated parts. Provisions are included for sampling plans, inspection freq [...]
DIN
DIN 7981
1984
English

Cross recessed pan head tapping screws

DIN 6901 shall apply for the designation of tapping screws with captive washer components (tapping screw assemblies). DIN 4000-2-1 tabular layout of article characteristics shall apply for scre [...]
DIN
DIN 434
1990
English

Square taper washers for use with channel sections

Washers as specified in this standard are intended for use in structural bolting of channel sections using bolts up to property class 5.6.
ASTM
ABSTRACT OF ASTM F1852
2008
English

“TWIST OFF” TYPE TENSION CONTROL STRUCTURAL BOLT/NUT/WASHER ASSEMBLIES, STEEL, HEAT TREATED, 120/105 KSI MINIMUM TENSILE STRENGTH

1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as “sets." These assemblies are capable of developing a minimum pred [...]