ASTM F912

ALLOY STEEL SOCKET SET SCREWS

English 2004
0.000
ASTM
Detailed Information

1.1 This specification covers the requirements for quenched and tempered alloy steel socket-set screws (SSS) 0.060 through 2.000-in. sizes having hardnesses 45 to 53 HRC.

1.2 These set screws are intended for compression applications only and are not customarily subjected to embrittlement tests. For tensile applications, consult with the manufacturer for proper alloy and hardness.

1.3 The hazard statement pertains only to the test method section, Section 11 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

NOTE 1-A complete metric companion to Specification F912 has been developed一F912M; therefore, no metric equivalents are shown in this Specification.

Download File
(Log in to download spec.)

Check out other specifications

DIN
DIN 7985
1972
English

Recessed Raised Cheese (Fillister) Head Screws

Normally, these screws are manufactured in the sizes for which weight details are given. If the screws are to be supplied with captive washer components, the designation must be augmented accor [...]
ISO
ISO 15071
1999
English

Hexagon bolts with flange — Small series — Product grade A

This International Standard specifies the characteristics of hexagon bolts with flange, small series, with product grade A, with threads from M5 up to and including M16 and property classes 8.8 [...]
ASTM
Abstract of ASTM F468
2001
English

NONFERROUS BOLTS, HEX CAP SCREWS, AND STUDS FOR GENERAL USE

1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs 0.250 to 1.500 in. inclusive in diameter manufactured from a number of alloys i [...]
DIN EN
DIN EN 1666
1998
English

Prevailing torque type hexagon nuts with flange (with non-metallic insert), with metric fine pitch thread (ISO 12125: 1997, modified) English version of DIN EN 1666

This European Standard specifies the characteristics of prevailing torque type hexagon nuts with flange, with non-metallic annular insert and metric fine pitch thread with nominal thread diamet [...]
ISO
ISO 2009
1983
English

Slotted countersunk head screws (common head style) – Product grade A

This International Standard specifies the characteristics of slotted countersunk head screws in product grade A and with thread sizes M 1,6 to M 10 inclusive.
ISO
ISO 4161
1983
English

Hexagon nuts with flange – Product grade A

This International Standard specifies the characteristics of hexagon nuts with flange with thread sizes from M 5 to M 20 inclusive, in Product grade A.
ASTM
ASTM F2280
2008
English

“TWIST OFF” TYPE TENSION CONTROL STRUCTURAL BOLT/NUT/WASHER ASSEMBLIES, STEEL, HEAT TREATED, 150 KSI MINUMUM TENSILE STRENGTH

1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as "sets," having a tensile strength of 150 to 173 ksi. These assemb [...]
DIN
DIN 562
1987
English

Square thin nuts Product grade B

This standard specifies requirements for M1,6 to M10 square thin nuts assigned to product grade B. If, in special cases, nuts are to comply with specifications other than those given in this st [...]
ASTM
Abstract of ASTM A325
2002
English

STRUCTURAL BOLTS, STEEL, HEAT TREATED, 120/105 KSI MINIMUM TENSILE STRENGTH

1.1 This specification covers two types of quenched and tempered steel heavy hex structural bolts having a minimum tensile strength of 120 ksi for sizes 1.0 in. and less, and 105 ksi for sizes [...]