BS EN 10025-2

Hot rolled products of structural steels — Part 2: Technical delivery conditions for non-alloy structural steels

English 2004
0.000
BS EN
Detailed Information

Part 2 of this document, in addition to Part 1, specifies the technical delivery conditions for flat and long products and semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 2 to 6 (chemical composition) and Tables 7 to 9 (mechanical properties) in the delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 3 and 5) (chemical composition) and Table 8 (mechanical properties). This document does not apply to structural hollow sections and tubes (see EN 10210-1 and EN 10219-1).

The technical delivery conditions apply to thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S450J0. The technical delivery conditions apply to thicknesses ≤ 250 mm for flat and long products of all other grades and qualities. In addition for flat products of qualities J2 and K2 the technical conditions apply to thicknesses ≤ 400 mm.

Products made of steel grades S185, E295, E335 and E360 cannot be CE marked.

The steels specified in this Part 2 are not intended to be heat treated except products delivered in delivery condition +N. Stress relief annealing is permitted (see also the NOTE in 7.3.1.1 of EN 10025-1:2004). Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).

Download File
(Log in to download spec.)

Check out other specifications

JIS
JIS B 1118
1995
English

Square head set screws

This Japanese Industrial Standard specifies the steel square head set screws (hereafter referred to as "steel set screws") and stainless steel square head set screws (hereafter referred to […]
JIS
JIS B 1041
1993
English

Fasteners—Surface discontinuities— Part 1 : Bolts, screws and studs for general requirements

This Standard establishes limits for various types of surface discontinuities on bolts, screws and studs for general requirements. It applies to bolts, screws and studs with — nominal thre […]
JIS
JIS B 1128
2004
English

Hexalobular socket head tapping screws

This Standard specifies the characteristics of hexalobular socket head tapping screws with nominal thread size from ST2.9 to ST6.3. If specifications other than those listed in this Standar […]
5.01
ASTM
ASTM F871M
1998
English

Standard Specification for Electrodeposited Coatings on Threaded Components [Metric]

1.1 This specification covers dimensional requirements for electrodeposited coating on threaded fasteners with M metric threads. It establishes a service condition classification for these […]
BS EN ISO
BS EN ISO 2768-2
1989
English

General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications

This part of ISO 2768 is intended to simplify drawing indications and specifies general geometrical tolerances to control those features on the drawing which have no respective individual i […]
JIS
JIS B 1003
2003
English

Fasteners — Ends of parts with external ISO metric thread

This Standard specifies the form and dimensions of ends of parts with external ISO metric screw thread (e.g., bolt and screw ends) recommended for use. They apply to standardized or non-sta […]
JIS
JIS B 0205-4
2001
English

ISO general purpose metric screw threads — Part 4: Basic dimensions

This Standard specifies the basic dimensions, in milimetres, of ISO metric screw threads in accordance with JIS B 0205-2. The values refer to the basic profile in accordance with JIS B 0205-1.
ASTM
Abstract of ASTM F1136
1993
English

CHROMIUM/ZINC CORROSION PROTECTIVE COATINGS FOR FASTENERS

1.1 This specification covers the basic requirements for three grades of chromium/zinc inorganic coatings for threaded fasteners. 1.2 These coatings are applied by conventional dip-spin or […]
NASM
NASM 24671
1998
English

SCREW, CAP, SOCKET HEAD, FLAT COUNTERSUNK, 82°, CORROSION-RESISTING STEEL, UNC-3A

MATERIAL: STEEL CORROSION-RESISTING, IN ACCORDANCE WITH FED. STD No 66; AISI 302. 303. 304, 305. 316 OR 384 (DEVELOPED FOR COLD HEADING). MINIMUM ULTIMATE TENSILE STRENGTH SHALL BE 80.000 P […]