DIN 1681

Cast steels for general engineering purposes – Technical delivery conditions

English 1985
0.000
DIN
Detailed Information

1.1 This standard applies to the grades of cast steel listed in table 1 with specified minimum values for the mechanical properties at ambient temperature. The castings made from these steels are predominantly used at temperatures between -10 and + 300°C.

1.2 See DIN 17 182 for cast steel grades with improved weldability and greater toughness for general engineering purposes.

1.3 This standard does not apply to heat resisting ferritic cast steel (see DIN 17 245), cast steel with low temperature toughness (see Stahl-Eisen-Werkstoffblatt (Iron and steel materials sheet) 685) and cast steel for quenching and tempering (see Stahl-Eisen-Werkstoff-blätter 510 and 515).

1.4 Unless otherwise specified below, the general technical delivery conditions for steel castings specified in DIN 1690 Part 1 and DIN 1690 Part 2 shall apply in addition to the specifications of this standard.

Download File
(Log in to download spec.)

Check out other specifications

ASTM
Abstract of ASTM F880
2002
English

STAINLESS STEEL SOCKET SET SCREWS

1.1 This specification covers the requirements for austenitic grade stainless steel socket set screws (SSS). sizes 0.060 through 0.500 in. in two conditions, AF and CW.
DIN
DIN 1152
1973
English

Round lost head wire nails

Wire nails shall be made of steel (grade at manufacturer’s discretion) and have a bright (bk) or galvanized (zn) finish.
ASTM
ASTM F606
2010
English

TEST METHODS FOR DETERMINING THE MECHANICAL PROPERTIES OF EXTERNALLY AND INTERNALLY THREADED FASTENERS, WASHERS, AND RIVETS

1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension ind [...]
ASTM
ASTM A563
1997
English

Standard Specification for Carbon and Alloy Steel Nuts

1.1 This specification covers chemical and mechanical requirements for eight grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other external [...]
ASTM
ASTM C954
2010
English

STEEL DRILL SCREWS FOR THE APPLICATION OF GYPSUM PANEL PRODUCTS OR METAL PLASTER BASES TO STEEL STUDS FROM 0.033 IN. (0.84 mm) TO 0.112 IN. (2.84 mm) IN THICKNESS

1.1 This specification covers minimum requirements for steel drill screws for use in fastening gypsum panel products or metal plaster bases to steel members from 0.033 in. (0.84 mm) to 0.112 in [...]
ISO
ISO 2009
1983
English

Slotted countersunk head screws (common head style) – Product grade A

This International Standard specifies the characteristics of slotted countersunk head screws in product grade A and with thread sizes M 1,6 to M 10 inclusive.
DIN EN
DIN EN 28765
1992
English

Hexagon head bolts with metric fine pitch thread – Product grades A and B (ISO 8765 : 1988) English version of DIN EN 28 765

This International Standard gives specifications for hexagon head bolts with metric fine pitch thread with nominal thread diameters d from 8 to 64 mm of product grade A for nominal thread diame [...]
DIN
DIN 267-9
1979
English

Mechanical Fasteners – Technical Conditions of Delivery – Components with Electroplated Coatings

These technical conditions of delivery apply to mechanical fasteners (mainly bolts and nuts) with electroplated coatings.
2.01
NASM
NASM 16555
1999
English

PIN, STRAIGHT, HEADLESS (DOWEL) (.0002 OVER NOMINAL SIZE)

CARBON OR ALLOY STEEL PINS SHALL HAVE A CORE HARDNESS OF 47-58 HRC, AND A CASE HARDNESS OF 60 HRC MINIMUM. THE CORE HARDNESS OF THE PINS SHALL NOT IN ANY INSTANCE EXCEED THE CASE HARDNESS. MINI [...]