JIS B 1053

Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5 : Set screws and similar threaded fasteners not under tensile stresses

English 1999
0.000
JIS
Detailed Information

This Standard specifies the mechanical properties of set screws and similar threaded fasteners not under tensile stresses with nominal thread diameters from 1.6 mm up to and including 24 mm, which are made of carbon steel or alloy steel (hereafter referred to as “set screws”).

The mechanical and physical properties apply when tested at an ambient temperature of 10 °C to 35 °C and will vary at higher or lower temperatures.

This Standard does not apply to set screws requiring special properties such as
— specified tensile stresses (see JIS B 1051);
— weldability;
— corrosion resistance;
— ability to withstand temperatures above + 300 °C or below -50 °C.

Download File
(Log in to download spec.)

Check out other specifications

ASTM
Abstract of ASTM F912
2000
English

ALLOY STEEL SOCKET SET SCREWS

1.1 This specification covers the requirements for quenched and tempered alloy steel socket set screws (SSS) 0.060 thru 2.000 in. sizes having hardnesses 45 to 53 HRC. 1.2 These set screws are [...]
ISO
ISO 14579
2001
English

Hexalobular socket head cap screws

This International Standard specifies the characteristics of hexalobular socket head cap screws with thread sizes from M2 up to and including M20, of product grade A.
ASTM
Abstract of ASTM A574
2000
English

ALLOY STEEL SOCKET HEAD CAP SCREWS

1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket head cap screws, 0.060 through 4 in. in diameter where high strength is required. NOTE 1 - A [...]
ASTM
Abstract of ASTM F594
2002
English

STAINLESS STEEL NUTS

1.1 This specification covers the requirements for stainless steel nuts 0.25 to 1.50 in. in nominal diameter inclusive in a number of alloys in common use and intended for service applications [...]
ASTM
ASTM F2280
2008
English

“TWIST OFF” TYPE TENSION CONTROL STRUCTURAL BOLT/NUT/WASHER ASSEMBLIES, STEEL, HEAT TREATED, 150 KSI MINUMUM TENSILE STRENGTH

1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as "sets," having a tensile strength of 150 to 173 ksi. These assemb [...]
ASME
ABSTRACT OF ASME B1.3
2007
English

SCREW THREAD GAGING SYSTEMS FOR ACCEPTABILITY: INCH AND METRIC SCREW THREADS (UN, UNR, UNJ, M, AND MJ)

(a) This Standard presents screw thread gaging systems suitable for determining the acceptability of inch UN, UNR, and UNJ screw threads on externally and internally threaded products. It estab [...]
DIN
DIN 961
1990
English

M8 x 1 to M52 x 3 hexagon head bolts with fine pitch thread – Product grades A and B

This standard specifies requirements for M8 to M52 hexagon head bolts threaded up to the head. with metric fine pitch thread, assigned to product grade A for sizes up to M24 and lengths not exc [...]
DIN
DIN 562
1987
English

Square thin nuts Product grade B

This standard specifies requirements for M1,6 to M10 square thin nuts assigned to product grade B. If, in special cases, nuts are to comply with specifications other than those given in this st [...]
DIN
DIN 7504
1995
English

Self-drilling tapping screws – Dimensions, requirements and testing

This standard specifies dimensions. requirements and test methods for heat-treated self-drilling tapping screws ('tapping screws' for short). These screws have a drill point with which they for [...]