NASM 16555

PIN, STRAIGHT, HEADLESS (DOWEL) (.0002 OVER NOMINAL SIZE)

English 1999
0.000
NASM
Detailed Information

CARBON OR ALLOY STEEL PINS SHALL HAVE A CORE HARDNESS OF 47-58 HRC, AND A CASE HARDNESS OF 60 HRC MINIMUM. THE CORE HARDNESS OF THE PINS SHALL NOT IN ANY INSTANCE EXCEED THE CASE HARDNESS. MINIMUM PENETRATION FOR THE CASE HARDNESS SHALL NOT BE LESS THAN .020 INCH. PINS 1/16 INCH AND LESS IN DIAMETER MAY HAVE A HARDNESS OF 58-64 HRC THROUGHOUT. CORROSION RESISTANT STEEL PINS, TYPE 416 (UNS S41600) OR TYPE 410 (UNS S41600) SHALL HAVE A HARDNESS OF 36-42 HRC.

Download File
(Log in to download spec.)

Check out other specifications

ISO
ISO 3269
2000
English

Fasteners — Acceptance inspection

1.1 This International Standard specifies the acceptance inspection procedure that the purchaser of fasteners must follow in order to determine whether a lot of fasteners will be accepted or re [...]
DIN
DIN 267-10
1988
German

Mechanische Verbindungselemente – Technische Lieferbedingungen – Feuerverzinkte Teile

Diese Technischen Lieferbedingungen gelten für mechanische Verbindungselemente {im wesentlichen Schrauben und Muttern) mit Regelgewinde M 6 bis M 36 und mit Zinküberzügen durch Feuerverzinken s [...]
BS EN
BS EN 10025-6
2009
English

Hot rolled products of structural steels — Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition

Part 6 of this document, in addition to part 1, specifies requirements for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 2 to 4 (chemic [...]
DIN
DIN 124
1993
English

Steel round head rivets with nominal diameters from 10 to 36 mm

This standard specifies dimensions of steel round head rivets with nominal diameters from 10 to 36 mm.
DIN
DIN 605
1981
English

Flat countersunk square neck bolts with long square

This standard specifies flat countersunk square neck bolts with long square, with metric threads M 6, M 8 and M 10, of product grade C.
DIN
DIN 960
1970
German

Sechskantschrauben – Metrisches Feingewinde – Ausführung m und mg

Eingeklammerte Größen sind möglichst zu vermeiden. Üblicherweise werden diese Schrauben in den durch Gewichtsangabe gekennzeichneten Größen hergestellt. Technische Lieferbedingungen noch DIN 267
DIN EN
DIN EN 20898-2
1994
English

Mechanical properties of fasteners – Nuts with coarse pitch thread and specified proof load values (ISO 898-2 : 1992) English version of DIN EN 20898 Part 2

This International Standard specifies the mechanical properties of nuts with specified proof load values when tested at room temperature (see ISO 1). Properties will vary at higher and lower te [...]
ASTM
ASTM A449
1993
English

Standard Specification for Quenched and Tempered Steel Bolts and Studs

1.1 This specification covers the chemical and mechanical requirements for two types of quenched and tempered steel bolts and studs for general applications where high strength is required. 1.2 [...]
DIN
DIN 6900-4
1990
English

Screw and washer assemblies – Coarse threaded screws with captive serrated lock washer

This standard specifies requirements for screw and washer assemblies consisting of a M2,5 to M10 screw with flat bearing face, assigned to a property class below 5.8, and a captive serrated loc [...]