NASM 35307

SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), STEEL, CORROSION RESISTING, PASSIVATED, UNC-2A

English 1999
0.000
NASM
Detailed Information

MECHANICAL PROPERTIES: The minimum tensile strength in load pounds, indicated in Table I is based on 80,000
PSI Minimum Tensile Strength for diameters through .625 inch and 70,000 PSI Minimum Tensile Strength for
diameters over .625 inch. The yield strength, based on 2 percent offset, shall be 30,000 psi minimum. The minimum
hardness shall be HRB 80 for diameters through .625 inch and HRB 74 for diameters over .625 inch.

Download File
(Log in to download spec.)

Check out other specifications

DIN EN
DIN EN 28765
1992
English

Hexagon head bolts with metric fine pitch thread – Product grades A and B (ISO 8765 : 1988) English version of DIN EN 28 765

This International Standard gives specifications for hexagon head bolts with metric fine pitch thread with nominal thread diameters d from 8 to 64 mm of product grade A for nominal thread diame [...]
DIN
DIN 315
1983
English

Wing nuts

The following amendments have been made in comparison with the December 1972 edition: a) The dimensions of the wing nuts have been altered in some respects. b) Limiting sizes have been adopted. [...]
NASM
NASM 35275
1999
English

SCREW, MACHINE-DRILLED FILLISTER HEAD, SLOTTED, CORROSION RESISTING STEEL, PASSIVATED, UNC-2A

DRILLED HOLE IS TO BE APPROXIMATELY AT RIGHT ANGLES TO THE SLOT AND MAY BE PERMITTED TO BREAK THROUGH THE BOTTOM OF THE SLOT. ALL SHARP EDGES SHALL BE REMOVED.
Others
NF E 25-511
1984
French

RONDELLES CONIQUES STRIÉES DE SERRAGE Symbole CS

La présente norme fixe les caractéristiques des rondelles coniques striées de serrage en acier au carbone, et définit les essais à effectuer pour leur contrôle. Elles sont généralement utilis [...]
ASTM
ASTM F880
2008
English

STAINLESS STEEL SOCKET-SET SCREWS

1.1 This specification covers the requirements for austenitic grade stainless steel socket-set screws (SSS) sizes 0.060 through 0.500 in., in two conditions, AF and CW. 1.2 Units一The values s [...]
ISO
ISO 8734
1997
English

Parallel pins of hardened steel and martensitic stainless steel (Dowel pins)

This International Standard specifies the characteristics of parallel pins (dowel pins) of steel, through hardened or case hardened and martensitic stainless steel with nominal diameters, d, fr [...]
NASM
NASM 35206
2004
English

SCREW, MACHINE-PAN HEAD, CROSS-RECESSED, CARBON STEEL, CADMIUM PLATED, UNC-2A

THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28/2. ACCEPTABILITY OF SCREW THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28/20, SYSTEM 21.
DIN EN
DIN EN 10270-1
2012
English, German

Steel wire for mechanical springs – Part 1: Patented cold drawn unalloyed spring steel wire

1.1 This European Standard applies to patented cold drawn unalloyed steel wire of circular cross-section for the manufacture of mechanical springs for static duty and dynamic duty applications. [...]
ISO
ISO 4753
2011
English

Fasteners – Ends of parts with external ISO metric thread

This International Standard specifies the form and dimensions of ends of parts with external ISO metric screw thread (e.g. bolt, screw and stud ends) recommended for use. They apply to standard [...]