ASTM Archives - Fasten.one

2009

English

STANDARD PRACTICE FOR FASTENER SAMPLING FOR SPECIFIED MECHANICAL PROPERTIES AND PERFORMANCE INSPECTION

Throughout this practice the terms detection and prevention apply to quality control systems. A brief description of both is provided to assist the purchaser in the application of this practice [...]

ASTM

Abstract of ASTM F812/F812M

2007

English

SURFACE DISCONTINUITIES OF NUTS

This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of inch-series nuts with nominal diameters [...]

ASTM

Abstract of ASTM F788/F788M

2008

English

SURFACE DISCONTINUITIES OF BOLTS, SCREWS, AND STUDS

This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolt, screws, and studs, including heat- [...]

ASTM

ASTM F606

2010

English

TEST METHODS FOR DETERMINING THE MECHANICAL PROPERTIES OF EXTERNALLY AND INTERNALLY THREADED FASTENERS, WASHERS, AND RIVETS

1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension ind [...]

ASTM

ASTM F2329

2005

English

ZINC COATING, HOT-DIP, REQUIREMENTS FOR APPLICATION TO CARBON AND ALLOY STEEL BOLTS, SCREWS, WASHERS, NUTS AND SPECIAL THREADED FASTENERS

1.1 This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners applied by the hot-d [...]

ASTM

ASTM F1941

2010

English

ELECTRODEPOSITED COATINGS ON THREADED FASTENERS (UNIFIED INCH SCREW THREADS (UN/UNR))

This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with unified inch screw threads. It specifies coating thickne [...]

ASTM

ASTM B695

2009

English

COATINGS OF ZINC MECHANICALLY DEPOSITED ON IRON AND STEEL

This specification covers the requirements for a coating of zinc mechanically deposited on iron and steel basis metals. The coating is provided in several thicknesses up to and including 107 μm [...]

ASTM

ASTM F2437

2006

English

CARBON AND ALLOY STEEL COMPRSSIBL-WASHER-TYPE DIRECT TENSION INDICATORS FOR USE WITH CAP SCREWS, BOLTS, ANCHORS, AND STUDS

1.1 This specification covers the requirements for carbon and alloy steel compressible-washer-type direct tension indicators capable of indicating a specified bolt tension in cap screws, bolts, [...]

ASTM

ASTM F436

2010

English

HARDENED STEEL WASHERS

This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1/4 through 4 in. These was [...]

ASTM

ASTM C1513

2010

English

STEEL TAPPING SCREWS FOR COLD-FORMED STEEL FRAMING CONNECTIONS

This specification covers steel self-drilling and self-piercing tapping screws for the connection of cold-formed steel members manufactured in accordance with Specifications C645 and C955. This [...]

ASTM

ASTM C1002

2007

English

STEEL SELF-PIERCING TAPPING SCREWS FOR THE APPLICATION OF GYPSUM PANEL PRODUCTS OR METAL PLASTER BASES TO WOOD STUDS OR STEEL STUDS

1.1 This specification covers steel self-piercing tapping screws for use in fastening gypsum panel products and metal plaster bases to cold-formed steel studs less than 0.033 in. (0.84 mm) in t [...]

ASTM

ASTM C954

2010

English

STEEL DRILL SCREWS FOR THE APPLICATION OF GYPSUM PANEL PRODUCTS OR METAL PLASTER BASES TO STEEL STUDS FROM 0.033 IN. (0.84 mm) TO 0.112 IN. (2.84 mm) IN THICKNESS

1.1 This specification covers minimum requirements for steel drill screws for use in fastening gypsum panel products or metal plaster bases to steel members from 0.033 in. (0.84 mm) to 0.112 in [...]

ASTM

ASTM F901

2001

English

ALUMINUM TRANSMISSION TOWER BOLTS AND NUTS

1.1 This specification covers aluminum structural bolts and nuts for use in the construction of aluminum transmission towers, substations, and similar aluminum structures. 1.2 Diameters of bolt [...]

ASTM

ASTM F594

2009

English

STAINLESS STEEL NUTS

This specification covers the requirements for stainless steel nuts 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications re [...]

ASTM

ASTM F467

2008

English

NONFERROUS NUTS FOR GENERAL USE

1.1 This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for general servi [...]

ASTM

ASTM A563

2007

English

CARBON AND ALLOY STEEL NUTS

1.1 this specification covers chemical and mechanical requirements for eight grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other external [...]

ASTM

Abstract of ASTM A194/A194M

2010

English

CARBON AND ALLOY STEEL NUTS FOR BOLTS FOR HIGH PRESSURE OR HIGH TEMPERATURE SERVICE, OR BOTH

1.1 This specification covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range 1/4 through 4 in. nominal. It also covers austenitic stainless steel nuts in the [...]

ASTM

ASTM F2280

2008

English

“TWIST OFF” TYPE TENSION CONTROL STRUCTURAL BOLT/NUT/WASHER ASSEMBLIES, STEEL, HEAT TREATED, 150 KSI MINUMUM TENSILE STRENGTH

1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as "sets," having a tensile strength of 150 to 173 ksi. These assemb [...]

ASTM

ABSTRACT OF ASTM F1852

2008

English

“TWIST OFF” TYPE TENSION CONTROL STRUCTURAL BOLT/NUT/WASHER ASSEMBLIES, STEEL, HEAT TREATED, 120/105 KSI MINIMUM TENSILE STRENGTH

1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as “sets." These assemblies are capable of developing a minimum pred [...]

ASTM

ASTM F959

2009

English

COMPRESSIBLE-WASHER-TYPE DIRECT TENSION INDICATORS FOR USE WITH STRUCTURAL FASTENERS

1.1 This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a structural b [...]